Check Engine Code Help

[jfrabat]

OK, guys... For the time being I swapped back to the 2.5L TB, and the engine is running a little better. The engine still stutters at about 4,000 RPM's, and will not go any higher than that (even while revving it up on neutral), but at least it is driveable now. But I am also getting a CHECK ENGINE light, and I cannot figure out what it is. I did the ignition switch thing, but I cannot figure out the number it is giving me, so I filmed a short video of it so that you guys can help me out.

If anyone is interested, please let me know your e-mail, and I will mail it to you (it's bout 300KB, so it's not long, but I cannot posted because it is more than 97KB zipped, and there is a block for mpg extensions).

Before the video was shot, I first got the light go on for about 5 seconds, then the secuence in the video. I THINK it is reading a 12, then a 13, not counting the first time the CHECK ENGINE light comes on, but I am so NOT sure, I preffer to have you guys look at it first. After the secuence, I get a 5 5 code, which is suppossed to mean there is nothing else to show (or at least I THINK it is a 5 5 code!).

By the way, is there any reader out there that will work with this computer and that will not cost a fortune? I know the '96 and above readers are about $100, but have not seen any for my car...

Can you guys help me with this? Maybe I will FINALLY figure out what the problem is!

Felipe

[Snitty]

I don't think your JEEP is going to be too happy with you for very long. You and your JEEP might not have a great relationship very soon if you don't give it the respect it deserves. Bounty pointed this problem out before, anyone else see the same thing I do?

(I'm only crackin jokes, so don't worry if this is over your head)

[mud4feet]

Originally Posted by jfrabat

..........I know the '96 and above readers are about $100, but have not seen any for my car.......

like that????

[jfrabat]

OK, OK, so I ran out of words for Jeep... It's my English Teacher's fault;l he's the one that tought me you have to not repeat the words too many times, and I have used Jeep, Rig, and beast much too often.

Then again, I can always use the excuse that english is not my first language!

But I think I'll go with "I'll apologize to my Jeep" way!

Felipe

[Sparky-Watts]

Originally Posted by Snitty

I don't think your JEEP is going to be too happy with you for very long. You and your JEEP might not have a great relationship very soon if you don't give it the respect it deserves. Bounty pointed this problem out before, anyone else see the same thing I do?

(I'm only crackin jokes, so don't worry if this is over your head)

[mud4feet]

Originally Posted by jfrabat

............But I think I'll go with "I'll apologize to my Jeep" way!

Felipe

HAHAHAHA!!!! I'm sure your apology will be accepted!! Glad you took the ribbing well..............I hate it when I do stuff like that!

[jfrabat]

Mud,

I kind of caught myself in the act (after I did it, anyway), but figured it would slip by. I guess you are all paying more attention to my posts than I thought! HAHAHA!

Felipe

[jfrabat]

Originally Posted by mud4feet

HAHAHAHA!!!! I'm sure your apology will be accepted!!

Mud,

It seems the Jeep (ie. NOT A CAR!) accepted my apologies, as it is running smoothly now! GO FIGURE!

Felipe

[aw12345]

Go to autozone they have a code reader and will read your codes for free

Art

[jfrabat]

Thanks, aw, but I already got myself a code scanner that not only reads my Jeep (pre OBD II, since it is before 1996), but OBDIIs and other pre '96 cars as well...

[Heydace]

IIRC, a code 13 is for the o2 sensor. Can your scanner read the o2 data or fuel trim? If o2 voltage is stuck high the PCM will lean out the fuel (shorter injector pulse width), which may explain the sputter at 4k rpm. The O2 should switch regularly above and below .45v.