10-05-2003, 07:06 PM
|
|
Senior Member
|
|
Join Date: Aug 2003
Location: Shoshone, ID
Posts: 619
|
|
I replaced my tranny mount because my transfer case was sitting on the skid plat. I figured the mount was bad. Pick up a new on and went to install it. It came with 2 rubber bushing things. I have no Idea where they go. The mount went right on to the tranny and the skid plate but the t-case still sits on the skid plate. Do the rubber things go between the skid plate and the mount? The grooves in the rubber bushings don't match any holes.
__________________
80 CJ5 258, T-176, D300, D30, M20, Tera Flex Discos, Blazer Blower, Power Stearing, Power Brakes, Detroit Locker, Superior shafts, 32\" Mud Kings
|
|
|
|
Sponsored Links - Removed for registered members
|
|
|
10-05-2003, 07:17 PM
|
|
Senior Member
|
|
Join Date: Nov 2002
Location: arkansas, or 34*06'N-93*04'W
Posts: 2,052
|
|
|
are they circles w/ holes in the middle? if they are that are the thoque stud bushings they are to the drivers side of the tranny...
__________________
82 CJ5 that dont run.... and is no more.... 94 Z71
J, you wont be forgotten
|
|
|
10-05-2003, 07:30 PM
|
|
Senior Member
|
|
Join Date: Aug 2003
Location: Shoshone, ID
Posts: 619
|
|
|
Yes they are. About an inch diameter with a hole. Like a really think rubber washer with a tapered end that looks like it is supposed to go into a hole. Is it even part of the mount area? they are like 3/4 inch thick so they would not have fit with the old munt. It had studs and nuts. The new mount required bolts frim the skid plate so I used some I had laying around.
__________________
80 CJ5 258, T-176, D300, D30, M20, Tera Flex Discos, Blazer Blower, Power Stearing, Power Brakes, Detroit Locker, Superior shafts, 32\" Mud Kings
|
|
|
10-05-2003, 10:21 PM
|
 |
Senior Member
|
|
Join Date: Nov 2002
Location: Olean, NY
Posts: 5,644
|
|
|
one goes over the bracket on the Tcase, one goes between the bracket and the skid.. they are bushings to absorb shock either way it shifts
__________________
93 YJ 4.0
Spring Over, 33x12.50 Mastercraft Courser M/T, High Flow Exhaust, Diamondplate Rear Bumper, Trimmed Flares, 6\" spotters
We, the Sovereign People of the Universe, wish to live in peace. We live among you, but we are not of you.
|
|
|
10-06-2003, 02:07 PM
|
|
Senior Member
|
|
Join Date: Aug 2003
Location: Shoshone, ID
Posts: 619
|
|
|
But there are 2 bolts so so they bo in between the bolts? There is no indentation to hold it.
__________________
80 CJ5 258, T-176, D300, D30, M20, Tera Flex Discos, Blazer Blower, Power Stearing, Power Brakes, Detroit Locker, Superior shafts, 32\" Mud Kings
|
|
|
|
Sponsored Links - Removed for registered members
|
|
|
| Thread Tools |
|
|
| Display Modes |
 Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 10:56 PM.
|
