Search results

You might want to contact Novak-adapters or AdvanceAdapters. Either one of those companies might beable to tell you the specifics. I have had good luck with Novak. They are very knowledgeble and easy to work with. Bacon Novak Jeep Conversions - Home Advance Adapters.Com Engine &...

That is a beautiful Jeep. You will not have any problems finding a good home for it. Bacon

I would say go. You might want to see if you can get the injection and puter along with it if they still exist. It would make off camber and high altitude adjustments a no brainer. And if the J10 dosn't work out for you and your buddy your only out a day or so of framing and can sell it or...

If you are not getting tire rub on either the springs or the body I wouldn't worry about spacers or new rims. I ran with Spidertrax spacers for about 6 months till I broke my rear pinion in the crappy d35. They kept the 35s from rubbing on my leaf springs at a full turn. I only used them on...

My 89 2.5L YJ did the same thing in Moab couple years ago. Turned out to be a failing fuel pump in the gas tank. It would run great while cool and for a little bit after that then it was a chore to get the rpm's over 3k. After i took the pump out it was slightly deformed as if it would heat...

Novak should have about everything you need. This link is for the GM v6's. Novak Engine Mounts

A lot of questions are answered in these 2 threads I found last year. E350 or Marquis master cylinder with rear discs? [Archive] - Pirate4x4.Com Bulletin Board Brake Upgrades Went with the 78 Grand Marquis because it is a direct bolt in. You can order them from Advance Autoparts it will...

I thought vin numbers were stamped onto the car in several places. Engine block (somewhere), inside the door, dashboard. I very well could be smoking some good stuff. Bacon

Yea, I know there are a lot of other good cages out there. It is just that Poison Spyder was 15minutes from where i live. Oh well. You snooze you lose, I slept and lost. Bacon

Crap, I was hoping to get their weld in full cage for my YJ.

Hey all, I am looking for a 241OR TC (rubicon 4:1 TC). I blew up the 231 in Oct of 06 up in Carnage just west of Boulder, Co. The jeep is a 89YJ with the mighty 2.5L. I am almost done with putting in a SM465 transmission with varrious Novak adapters. The preferred TC would be the STAK...

Matt, if it seems it is choking for gas maybe you need to change out the fuel filter. When the vehical is sitting or has been what ever debree it has filtered settles to the bottom of it and you get a fairly consistant flow of fuel but after time or bumps it will be pulled into the filter again...

You should easly beable to find one in your local junk yard. It wouldnt cost much either.

Novak adapt has some nice write ups on conversions, knowledge on engines, trannies etc. Chevrolet & GM Engine Conversions into the 1980-1986 Jeep CJ I had once found a site that made wiring harneses for various conversions and now for the life of me i can not find it again. But in the...

Do what Cewtwo suggests with using a ford 8.8 from an Explorer. Good axle and should very nearly swap right in. Make sure you swap out your brake proportioning valve so it can handle disc brakes in the rear. I am using a 90's valve from a grand cherokee. The disc brakes take higher pressure...

Anchor in some pullies into the ceiling. That way 1 person can lift and lower your top. I have mine rigged so i can back under it and lower the hard top into possition without blowing out my back.

Oink! Haha. ( I can almost hear dualing bango's in the back ground).

Novak has some great adapters aswell. Adapting Chevrolet & GM Engines to the Jeep AX15 Transmission

Did you have to change the gearing to compensate for the larger tire and greater mass? What is its gas milage like now?

Meet'n'Greet i think i can make but unfortionatly the Jeep is still under the knife. Bacon