Search results

I got my jeep back from a clutch change. Now my shifter (5 speed) is sloppy and loose. What is the piece that goes in the base of the shifter below the boot called and who might have one? Can't go back to the shop. Thanks

A source for steering column horn parts is wanted. The plastic piece with 2 metal legs protruding from it under the bolt holding the key lock in place. Its held down with a straight spring.

Sorry , no photos

DIPSTICK TUBE BROKEN; Remove broken in block with 1/4" easy- out. Buy short piece of 1/4"(0.315)(outside) brake line tubing. Clean everything with acetone or a de-greaser. Cut brake tubing 2 to 3 inches long. Put a mark on the brake tubing at the half way point...in the middle of it. Coat...

Cj7 broken dip stick tube easy strong fix DIPSTICK TUBE BROKEN; Remove broken in block with 1/4" easy- out. Buy short piece of 1/4" brake line tubing. Clean everything with acetone or a de-greaser. Cut brake tubing 2 to 3 inches long. Put a mark on the brake tubing at the half way...

DIPSTICK TUBE BROKEN; Remove broken in block with 1/4" easy- out. Buy short piece of 1/4" brake line tubing. Clean everything with acetone or a de-greaser. Cut brake tubing 2 to 3 inches long. Put a mark on the brake tubing at the half way point...in the middle of it. Coat tubing with RIGHT...

MYSTERY SOLVED: banging sound at left front wheel. the answer is - loose top shock mount bolts. all else looks OK Thanks RET:verry-happy:

Sorry 1985 CJ7

My hubs or lockouts are banging. Just put in new wheel and spindle bearings, u-joints, rotors pads, seals and almost everything else. The lockouts are new superwench. It happens when in 4WD or 2WD. Locked or unlocked. Any help is appreciated. RT

Russels

I was reading elsewhere here about the AMC 20 rear axle swap. One person suggested to contact you as a good source for info on these. I have an 85 cj7 and would like to swap the 2 piece axles for one piece axles. Some places say they have axles welded together and others say theirs are...

Just picked one up at the wreckers. gm made the canisters. Use Mid 1970 to early 1980 canisters. Same dimensions . You might have to look hard for the right amount of ports on the top. I found one in a pickup. Also I found Cadillacs were a good choice to start with. I spent months...

Just picked one up at the wreckers. gm made the canisters. Use Mid 1970 to early 1980 canisters. Same dimensions . You might have to look hard for the right amount of ports on the top. I found one in a pickup. Also I found Cadillacs were a good choice to start with. I spent months...

Thanks. Rt

MAP SENSOR, yes. Voltage within specs. Howell called yesterday, said to raise idle to 850, time at 8 or 9 degrees, lower fuel pressure from 14 PSI. Said they can burn me a new chip. Whatever that means

Anyone?

Does anyone know how to improve a window regulator that jams 3 times as its rolled down or know where to get a new one? I took the hard doors apart and the drives side jams going down. I greased the gearing but doesnt help. Can these be adjusted somehow?

Just installed system but after 2 minutes it runs rich. Idle to 1500 rpm stays smooth but after that the engine stumbles and rpm falls off. Timing doesnt change anything. I get code 45 running rich but i don't know hat to do. Don't know shere ckt. 412 is to ground it per service manuel...

An engine mount is in the way of an oil pan bolt on the passenger side. How can I take the mount off and drop the pan at the same time? How can I hold up the engine with both off?

I'm bumping it up to 5/16th". Thats the fuel feed size. I was going to 3/8th" but limited space on top of the fuel tank and jeep body. TBI to sender tube inlet 5/16". Sender tube inlet is still 1/4' though.