Search results

I have a 1993 wrangler 4.0 Ax15 transmission. Some time ago I swaped out my interior slave to a exterior setup. my current clutch now has 93,000 miles. Taking off from a stop sign, I felt a slip and felt a vibration and a screeching noise from my transmission. I pulled over and crawled...

I was working on instaling brackets, parts and pieces on my new rebuilt 4.0 motor this afternoon. When I got to the fan clutch and pulley for the water pump, I noticed that the bolt pattern was a little narrower on the parts compared to the pump, and there was no protruding mounting nub on the...

I have a chance to pick up the sought after Dana 44 out of a 1989 Cherokee. Is it indeed a true drop in for a 1994 Cherokee, All brackets sway bars Greg

Time to upgrade my 4.0 with the fresh rebuild I just got through with. One question at the back of my mind is charging the cooling system somewhat before initial startup and cam break in. Do I just fill the radiator and overfill the reservoir the night before, and just let the thermostat open...

What is the correct idle speed for the 4.0 Cherokee xj. Mine idles at 1050 rpm hot, with Manual transmission.

Looking at picking up a Grampa jeep that has not even set foot in the dirt! 94 jeep Cherokee sport 4x4 with 104,000 miles:D I can see that the rear end is the Chrysler 10 1/4 27 spline I believe. Has anyone done a disc brake conversion on one of these?

Driving home today I spotted a 97 Cherokee sport on a used car lot. What really caught my eye on this was how nice and clean it looked. I stopped and talked to the salesman that only had maybe 15 minutes left on his shift, so I quickly took a peek. Few drips of oil here and there below the valve...

Does anybody know if the 93 wrangler and the 94 Cherokee share the same motor mounting brackets? Thanks, Greg.

Does anybody know the difference between 1993-1994 with the jeep 4.0 distributors? is the wireing pigtail different or the gear size? I know the pigtail on the 1993 is 3-prong. I'm going to instal a 1994 motor from a Cherokee into a 1993 wrangler and the doner did not come with the distributor...

I was test fitting a new melling oil pump to my 94 Cherokee 4.0 block this morning (test fit no gasket) and noticed a definite rocking back and fourth on the mateing surfaces. Checked with a straight edge and it is in the block not the pump surface. :?:Wondering if anyone else has noticed this...

Looking to instal larger flares on the wrangler to cover up the wider tires and wheels. Need a min of a 6" set. What is everyone's opinion on the best looking flares? I do want to stay away from cutting away sheet metal to make flares fit. 93 wrangler yj. Thanks, Greg.

Anyone out there have a 4.0 ho stock camshaft from a 91-95 jeep they could take some measurements from? Or have already measured. Purchased a mild reground upgrade RV1 from delta and gave them my old one for a core already. Just picked up my machined block and head and had a little more shaved...

:pHas anyone on here switched there vacuum disco's over to manual hubs? I just installed the Reid knuckles on a Dana 30 and was wondering how I could bypass the old 4wd indicater switch on the old housing and wire it so my 4wd light still works. I know it is not a big thing but would be cool if...

:-)Hello everyone, I am having a crankshaft balanced for a engine rebuild at a machine shop for a 1994 4.0 jeep wrangler with a manual transmission. I told my machinist I would drop him off a flywheel,vibration dampener and hardware. Having a hard time finding information on bolt sizes. I know...

I believe my YJ's fuel pump finally gave up the gost after 255,000 miles. At least it died in the driveway so all I had to do is nudge it into the garage with the pickup:p My question is from everyones experiance what is the pump to buy or the pump to stay away from? Is there the one that never...

I pulled my carrier out of my dana 30 axle today to regear and came accross a part that is not listed in my factory service manual, and the parts dealer has no idea what it is. On both sides of the carrier is a large O-ring? orange in color. It is between the drivers side oil seal and the...

I own a 1993 wrangler with the 4.0. Need to figure out soon what my next move is going to be for this transmission. My question: what years are exactly the same as my AX-15 for a drop and bolt right back up? Thanks in advance, Greg.

Has anyone on her succesfully instaled new syncronizers on one of these tranys? I switched over to royal purple some time ago and it shifted better for the longest time but now it is that time to do something else. Looking for any tips, techneques or special tools. Thanks, Greg. Sorry if...

Hello, I own a 1993 Wrangler with the 4.0 that just turned 227,000 that I bought brand new in 1993. I've always kept the maintenance up and use it as a daily driver and a hunting rig. I have never had any major issues with the running gear except for clutches and u-joint's. Two things that I...

Hello, I own a 1993 jeep wrangler 4.0 with the 5 speed AX-15. I have the internal slave that is leaking. I would like to switch to the external slave. So far I have the Bellhousing and the clutch release fork from a 1998 wrangler on the way, besides the throwout bearing and the external slave...