Radio install on a Wrangler

TerryMason

Administrator
Staff member
Installing an upgraded radio in your Wrangler is a pretty straight forward procedure. You simply remove the old one, connect the custom wiring harness to the new radio, install the radio, then button everything up.
 

Necessary components

You'll need a few items to get your new radio installed.

1. New radio
2. Wiring harness
3. faceplate
4. Amp install kit and amplifier (if you are installing an amp)
5. Antenna extension
 

Attachments

  • IMG_0362-jeep-radio-install.JPG
    IMG_0362-jeep-radio-install.JPG
    58 KB · Views: 699
  • IMG_0371-jeep-radio-install.JPG
    IMG_0371-jeep-radio-install.JPG
    65.7 KB · Views: 746
  • IMG_0350-jeep-radio-install.JPG
    IMG_0350-jeep-radio-install.JPG
    58.5 KB · Views: 1,007
Step 1 - Removing the stock radio

To remove the stock radio, you'll need to first pry up the plastic panel over the defroster vents. To pop this panel up, just poke your fingers through the grate over the vent.

Once you have the defroster cover up, you'll be able to remove the two bolts holding on the console cover.

After that, you'll be able to pull off the black cover over the center dash cover.
 

Attachments

  • IMG_0363-jeep-radio-install.JPG
    IMG_0363-jeep-radio-install.JPG
    61.6 KB · Views: 795
  • IMG_0365-jeep-radio-install.JPG
    IMG_0365-jeep-radio-install.JPG
    80.4 KB · Views: 1,259
  • IMG_0366-jeep-radio-install.JPG
    IMG_0366-jeep-radio-install.JPG
    78.8 KB · Views: 6,174
Step 2 - Removing the stock radio

To remove the stock radio, you'll need to first unbolt the for bolts on the front of the radio.

Now, remove the glovebox door and disconnect the antenna. It's the silver connector in the middle

Next comes the hard part. You'll need to use a socket wrench to reach through the glove box door, up behind the radio and unbolt the single nut holding the stock radio in. Once that's out, you'll be able to pull the radio out and unclip the stock wiring harness.
 

Attachments

  • IMG_0367-jeep-radio-install.JPG
    IMG_0367-jeep-radio-install.JPG
    82.5 KB · Views: 567
  • IMG_0368-jeep-radio-install.JPG
    IMG_0368-jeep-radio-install.JPG
    61.2 KB · Views: 362
  • IMG_0369-jeep-radio-install.JPG
    IMG_0369-jeep-radio-install.JPG
    104.7 KB · Views: 326
  • IMG_0372-jeep-radio-install.JPG
    IMG_0372-jeep-radio-install.JPG
    83.2 KB · Views: 674
Last edited:

Step 3 - Connecting the harness

The stock radio uses a proprietary connector, so to connect your new radio to the Jeep, you'll need an adapter. You'll need to purchase an adapter and connect the adapter to your new radio using the supplied wiring chart.

You can try twisting the wires together and taping them, or using scotch locks, but my preferred method is to solder the wires together.
 

Attachments

  • IMG_0354-jeep-radio-install.JPG
    IMG_0354-jeep-radio-install.JPG
    116.4 KB · Views: 848
  • IMG_0361-jeep-radio-install.JPG
    IMG_0361-jeep-radio-install.JPG
    108.7 KB · Views: 983
Step 4 - Replacing the radio

Once the wiring harness is completed, just plug it up, connect the antenna (using the extender), then insert the radio into the dash. Return the four bolts to hold the radio in and you're good to go.
 

Attachments

  • IMG_0374-jeep-radio-install.JPG
    IMG_0374-jeep-radio-install.JPG
    54.6 KB · Views: 1,392
  • IMG_0394-jeep-radio-install.JPG
    IMG_0394-jeep-radio-install.JPG
    86.9 KB · Views: 6,138
Installing the amplifier - Running the power

To install the amplifier, you'll need to first wire up the power wire (with fuse) directly to the battery. To go through the firewall, be sure to use a grommet.

Remember to route your main power wires away from the radio wires. I chose to route the power down the side of the Jeep, and the radio wires down the center.

To install the amp's ground wire, you'll need to find a good strong bolt into the body, then sand off the paint and bolt down the wire. I used the rear seat bracket for my ground spot.
 

Attachments

  • IMG_0406-jeep-radio-install.JPG
    IMG_0406-jeep-radio-install.JPG
    85.4 KB · Views: 3,369
  • IMG_0405-jeep-radio-install.JPG
    IMG_0405-jeep-radio-install.JPG
    99.8 KB · Views: 622
  • IMG_0397-jeep-radio-install.JPG
    IMG_0397-jeep-radio-install.JPG
    104 KB · Views: 351
  • IMG_0398-jeep-radio-install.JPG
    IMG_0398-jeep-radio-install.JPG
    79.4 KB · Views: 331
  • IMG_0400-jeep-radio-install.JPG
    IMG_0400-jeep-radio-install.JPG
    72.9 KB · Views: 414

Installing the amplifier - running the radio wires

You'll then need to route the radio wires to the amp. I installed my amp in the rear, and routed the radio wires under the center console, and then under the carpet to the amp.
 

Attachments

  • IMG_0391-jeep-radio-install.JPG
    IMG_0391-jeep-radio-install.JPG
    83.2 KB · Views: 1,610
  • IMG_0401-jeep-radio-install.JPG
    IMG_0401-jeep-radio-install.JPG
    72.9 KB · Views: 869
  • IMG_0404-jeep-radio-install.JPG
    IMG_0404-jeep-radio-install.JPG
    68.8 KB · Views: 505
  • IMG_0402-jeep-radio-install.JPG
    IMG_0402-jeep-radio-install.JPG
    57.1 KB · Views: 476
  • IMG_0403-jeep-radio-install.JPG
    IMG_0403-jeep-radio-install.JPG
    72.1 KB · Views: 565
Finished installing your Wrangler's radio

That's it, you're finished installing your radio, and can enjoy your new tunes!
 
Re: Finished installing your Wrangler's radio

this will help big time! 1st time installer and i love the pictures! :shades:
 
Back
Top