1. #1
    drummr25's Avatar
    drummr25 is offline Junior Member
    Join Date
    May 2019
    Posts
    1

    Time for a new axle??

    Hello all- new member here. Was under my 2015 HR Rubi last weekend doing the diffs, trans-axle and manual tranny oil change when I noticed some grease that had been flung around the top from the Driveshaft. I have a 3-1/2" Metal Cloak lift with just over 60K miles. I don't know much about this, but I've read that the more extreme your axle drop is, the harder things are on it- and that I could expect this to happen eventually with any lift over about 2". What say you? Thanks in advance for any/all help!
    Attached Thumbnails Attached Thumbnails Time for a new axle??-axle-pic-1.jpg  

    Time for a new axle??-axle-pic-2.jpg  

    Time for a new axle??-axle-pic-4.jpg  

    Last edited by drummr25; 05-17-2019 at 08:30 AM.

  2. #2
    vinn's Avatar
    vinn is offline Member
    Join Date
    Dec 2015
    Posts
    93

    Re: Time for a new axle??

    I bought my cj with a 2 inch lift. have had no problems with universals or oil seals. the ford bronco 11 had problems with universals. vin

  3. #3
    buttons276's Avatar
    buttons276 is offline Junior Member
    Join Date
    Jun 2019
    Location
    Yadkinville, NC
    Posts
    18

    Re: Time for a new axle??

    The cv type drive shafts are the same type in my grand Cherokee. I don’t know much about lifts but I can tell you these drive shafts can make some crazy noises. When mine went bad is honest to god sounded like someone was sticking an aluminum ball bat in a metal fan. I thought the engine had blown. But it looks like your boot just got worn out and it threw all the grease out. I see these come in the shop in this condition all the time. So you who knows how long it will last in that condition. Months or years. The drive shafts are super expensive but when mine went out I found a company online, in floridia I believe, that sold basically a rebuild kit. It came with everything to repair both ends. It’s been a year or two but it seems like it was around 100 bucks. Easy enough to do. The only special tool needed was the thing to tighten the band clamps.

  4. #4
    buttons276's Avatar
    buttons276 is offline Junior Member
    Join Date
    Jun 2019
    Location
    Yadkinville, NC
    Posts
    18

    Re: Time for a new axle??

    Did a quick search and looks like they are for sale everywhere now and have came down in price. Just make sure it’s the one for your Jeep. And even if only one end is bad I personally would go ahead and change both ends while you have the driveshaft out. I tried to post a pic but I’m new to the forum and couldn’t get it to upload. But just google “jeep cv driveshaft rebuild kit” and it will pop up

  5. #5
    vinn's Avatar
    vinn is offline Member
    Join Date
    Dec 2015
    Posts
    93

    Re: Time for a new axle??

    good boot question! changed a torn boot on an 88 caddy on one of two axles. later the other side tore. the boot kit was no longer avaiable. chineeze made boot was all you could get. sad, very sad! in

Similar Threads

  1. Removing Axle Bearing From Axle Shaft? AMC 20
    By ranman64 in forum CJ YJ TJ and JK
    Replies: 1
    Last Post: 02-15-2013, 11:22 AM
  2. Time for a rear axle swap. Dana 44
    By Jesse in forum CJ YJ TJ and JK
    Replies: 15
    Last Post: 03-08-2010, 01:27 PM
  3. 3rd time jeep owner...this time i got it right!
    By GenericEclipse in forum Cherokee, Commander, Wagoneer and Liberty
    Replies: 4
    Last Post: 06-18-2005, 11:24 PM
  4. part time vs full time
    By MudderChuck in forum Cherokee, Commander, Wagoneer and Liberty
    Replies: 7
    Last Post: 07-20-2003, 07:00 PM
  5. Looking For a f150 front axle or a 78-79 Bronco axle
    By Jeepin91 in forum Items for Sale, Trade, or Give Away
    Replies: 1
    Last Post: 07-20-2003, 07:00 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Log in

Log in