Recent content by Stuart

1041538 Thanks for the info. But I do have a follow on question....what all vehicles came with the Dana 44. Oh yeah the AC is for these HOT summers in Florida Thanks Len[addsig]

1041592 You may also want to check and make sure that your exhaust manifold is tight and that all of your clamps are providing a good seal. An exhaust leak can cause you to pop as well. [addsig]

1041593 If the light bar has its own switch you should be able to wire it from any fuse that has a lead that is hot all the time and then ground it to a good ground on the body.[addsig]

1041594 I took my CJ5 and installed two leather/power seats out of an 98 Grand Cherokee. All it took was a couple of pieces of 3x3 angle iron and tw pieces of 2x2 square tubing. Drill a coupe of new holes and you have a two new seats. I love mine I think they are about the most comfortable...

1041602 You could also try a set of easy outs. you need to take a dril and drill a hole into the head of the bolt. you then take the easy out, acresent wrench to turn it with and a hammer to smack it as you turn. Since the easyouts are left hand threaded as you tighten them it loosens the...

1041664 Im not sure about the gas smell but I have noticed that I get worse gas milage with the top down than I get with the top up.[addsig]

1041832 Hey kid, I have the 304 and T-150, also I am running an edelbrock 650. What size carb are you running on yours? [addsig]

1041925 I have the Edelbrock valve covers also and they are not vented. The motor seems to be in pretty good shape. It did sit for about 2 years without running. If the rings are bad would that cause this problem? Thanks Len[addsig]

1041927 When I rebuilt my CJ I went with a Stainless Fastner kit from quadratec. It has ever fastner that you would ever need. It may seem a bit expensive but you don't have to worry about scrounging around for fastners in decent shape and if you put a dab of anti-seize on them you will not...

1041937 I had thought about doing this but I wasn't sure exactly how to go about it. So did this fix your venting problem? What type of breather did you use? Did you get the breather and the gromet at AutoZone? thanks, Len [addsig]

1041601 I have the t-150 transmission withe the model 20 transfer case. After a rebuild I am having a problem with oil from the transmission migrating to the transfer case. the transfercase then fills up and oil come out of the vent cap. I think that this is the seal on the input shaft...

1041666 I am looking to replace my t-150 3-speed with at least a four speed and a five speed if at all possible. I am looking to run a little better gear ratio to try and help to improve gas milage. Does anyone know what transmissions mate up to the 304 bellhousing and also work with a model...

1041667 I am trying to clean the garage I I have a few parts that I need to get rid of. Just e-mail me if you are intrested and I will send any pictures that you would like. Buyer pays shipping. 1. Bestop soft half doors for cj5 2. Model 35 front axle shaft housing, both axle shafts...

1041901 I am having a problem with my 304 venting oil out of the filler spout. I have the edelbrock performer intake manifold and also the edelbrock 650 cfm carb. I have the pvc valve in the spot directly behind the carb and the vent hose pluged into the front of the carb where there is the...

1042202 Hi all I have a 76 cj5 with a 304 I cannot find the duct work that goes from the lower airbox to the defrost ducts any where. Does any one out there know where I can buy these pieces. I was also curious if anyone has swapped the entire interior air boxes and heater core out for a...