Search:

Type: Posts; User: jps4jeep; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    13
    Views
    4,403

    Re: New ring and pinion

    Mix your paint with a little (very little) gear oil, will make reading the contact pattern easier. If too thick, the marking compound will force the paint and give an off reading.
  2. Thread: Advice

    by jps4jeep
    Replies
    4
    Views
    2,301

    Re: Advice

    Backfires through the throttle body? are you getting a check engine light? 96 XJ is ODBI or ODBII, don't recall.
    I would start with something simple like looking for vacuum leaks around the...
  3. Replies
    7
    Views
    3,201

    Re: YJ t case swap

    I recommend IDing the problem first. a sound could be anything from a slacked out chain to a worn shifter fork. many parts from the dodge 231 will swap over to your jeep case. I believe all 21...
  4. Replies
    19
    Views
    4,716

    Re: The best winch for my Jeep?

    For every pulley added increases the line pull by fifty percent, two pulleys would net doubling. Am i wrong?

    I probably am, 6th grade physics was over thirty years ago.
  5. Replies
    19
    Views
    4,716

    Re: The best winch for my Jeep?

    Running cable from the winch to a winch point, through a snatch block and back to the vehicle does not double a winches pull strength. what i think he is referring to requires multiple snatch blocks...
  6. Replies
    26
    Views
    4,896

    Re: All my newb questions

    Put the winch on and forget about it. I would highly recommend keeping it covered when ever not in use. maintenance is limited to maybe servicing the motor or replacing a selonoid.
  7. Replies
    11
    Views
    1,983

    Re: drops out of 4x4

    CAD diaphragm on the pass side of the front axle. if it is intermittent, then it is probably a vacuum leak, if it is just not functioning, then it is junk. Google search posi lock or CAD MODS and you...
  8. Thread: page layout

    by jps4jeep
    Replies
    4
    Views
    6,982

    Re: page layout

    My wife's computer is showing as normal, must be something on my PC... and yes, the NSA is constantly monitoring my PC, if offroad websites and internet porn make me a threat, then so be it.
  9. Thread: page layout

    by jps4jeep
    Replies
    4
    Views
    6,982

    page layout

    Anyone elses page layout all screwy? Mine is and it makes it extremely difficult to navigate? I am going to check on a different computer tonight to see if it is a network thing on my end.
  10. Replies
    14
    Views
    3,753

    Re: In need of Traction bar

    The length from heim center to heim center as you see if is about 30" and at the axle, there is about 7" of separation. These numbers are not hard since there is some adjustability in the heims. That...
  11. Thread: Shifter knob

    by jps4jeep
    Replies
    9
    Views
    4,164

    Re: Shifter knob

    Not on TJ's.

    Also if you loose that cap, a beer bottle cap also fits in there snuggly for a "custom" look.
  12. Thread: question?

    by jps4jeep
    Replies
    5
    Views
    1,290

    Re: question?

    As long as they are properly gapped, I'll run any plug. I find that about 60% of the time, a pregapped plug is not gapped properly. Also stock wires are fine.
  13. Replies
    14
    Views
    3,753

    Re: In need of Traction bar

    The amount of lift is arbitrary. If you are staying spring under, you should not need a trac bar. If you still have spring wrap while SUA, you have some junk or broken springs.

    If you wanted,...
  14. Replies
    14
    Views
    3,753

    Re: In need of Traction bar

    You know what, I think I also still have the shackle that I bought to go along with this. Brand spanking new.

    I'll grab photos of everything tonight.
  15. Replies
    14
    Views
    3,753

    Re: In need of Traction bar

    To give you an idea, this is what the trac bar looks like (this is not the actual one)

    19629
  16. Replies
    14
    Views
    3,753

    Re: In need of Traction bar

    I don't see why it wouldn't work, it is just a trac bar. I'll snag a picture tonight and get all the critical measurements. I think I also have a set of axle mounts that you can weld on. (<-I...
  17. Re: YJ front & rear axle misaligned after2.5" susp lift

    Jeep YJ = No trac bars. You do not need them.
  18. Replies
    14
    Views
    3,753

    Re: In need of Traction bar

    Are you SOA? I have a trac bar that I built long time ago that was on the rear of a comanche project that I ended up linking. I am 99% sure I still have it in the shop. Made from DOM (I think...
  19. Replies
    7
    Views
    6,763

    Re: Taillight issues 1990 wrangler

    I would check for continuity with a ground on teh tail light wiring. Sounds like there is contact somewhere. IIRC, the tail lights should be on teh same curcuit as the park lights and come directly...
  20. Replies
    3
    Views
    1,948

    Re: plugs and gap for fuel injection

    I am not super familiar with the Howell system, but if it has a MAF and o2, it should be able to rear a rich condition and accomidate by leaning out fuel. How old is your fuel tank? IIRC for the...
  21. Re: How do I wire a 03 jeep Cherokee Motor (fuel injection) in to 86 jeep cj 7

    Does you new motor have a distributor?

    If it does, most likely did not come from a 03 and I would suggest wiring it up as if it was a 92-95 YJ using that vehicles ECM and ODBI system. then you...
  22. Replies
    7
    Views
    6,763

    Re: Taillight issues 1990 wrangler

    I would start with inspecting the wires from the tail lights forward and check for any bare wires of a place where someone hacked up the wiring for something like a trailer connection or an alarm.
    ...
  23. Replies
    3
    Views
    2,048

    Re: Where the World's Unsold Cars Go To Die

    It's fake. Well documented on Jalopnik
  24. Replies
    44
    Views
    8,972

    Re: What do you do for a living?

    Federal Investigator
  25. Thread: Motor swap

    by jps4jeep
    Replies
    4
    Views
    1,075

    Re: Motor swap

    Depends on the motor and how good are you are wiring.

    The questions you are asking ultimately rely on the person doing the works abilities, amount of time researching, and time planning in...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Log in

Log in