Search:

If you haven’t yet do a fuel pressure test. Steady at 49 psi +/-2 at idle and 3300 rpm and after engine off. Once off the pressure Should hold psi for more than 2 min.

Low fuel pressure.
Weak...

Correct you want the springs to be the limiting factor. Avoid the limiter being the brake lines or shocks.
If you have shocks for a 2 in lift and add 1.5 in spring spacers the shock will limit...

This is a bit old. But id check caster . Also check camber to tire height and width.
Toe is important but if you have less than 4 -5 deg caster the scrub is under the center of the tire providing...

I have to ask. Was the shock matched to the amount of lift? Does he 4 wheel and disconnect sway bars?
Shear indicates the shock was fully extended or received a shot with the force of an accident.
...

They use a <3 to indicate popular purchase. They used another mark for OEM equipment. Cant recall.


Never look down on anyone unless you are helping them up - Jesse Jackson

Is it me or is your drag link at a different angle than your track bar??

This leads to bump steer. Hit a bump and the wheel gets jerked out of your hand.


Never look down on anyone unless you...

Sure that’s not your wallet screaming?

Id change belt, tensioner and idler pulley


Never look down on anyone unless you are helping them up - Jesse Jackson

Sry
Check for local jeep clubs and ask where they go if they had to. Maybe the club has an expert.


Never look down on anyone unless you are helping them up - Jesse Jackson

Maybe its time to replace it??
I have a honda with a 2.4 engine the exhaust cam wears and galls. Every 30k mi the rockers need to be checked and regapped. Sucks had to replace the head. FYI
Reman...

Carb going to dribble dribble you know.


Never look down on anyone unless you are helping them up - Jesse Jackson

“My money don’t Jingle! Jingle! It folds. ….”


Never look down on anyone unless you are helping them up - Jesse Jackson

Yep force carb and choke cleaner through it. Does the float, float? Does the needle stop the flow? Rebuild kit $$14


Never look down on anyone unless you are helping them up - Jesse Jackson

What size tires and gearing? All stock?

Many write of this and rough ride/drivetrain. Check trans fluid. It could be the point the Torque Converter locks. Does it continue at higher rpm or speeds?...

Carpet aligner.


Never look down on anyone unless you are helping them up - Jesse Jackson

Is the noise under the hood or in the cabin? There is a valve for HVAC that is in the dash in many jeep models that clicks as it moves


As for starting. Gas air and spark. As noted start with gas...

Agree with The NSS issue after reading it only clicks when starting in park.


https://youtu.be/_qGt-NsVWV4


Could try this to verify. Dangerous!!! Needs to be in park
Neutral Safety Switch...

Crawl under look for rust…
Aftermarket parts…
Take it for a ride to heat it up…
Go to a mechanic or auto store and look for codes and that the data is set. If not set they may have removed the...

That is a lot of seafoam.
Every oil change is good.


Never look down on anyone unless you are helping them up - Jesse Jackson

The stalling at a light can be a few things. Start easy. Clean your Throttle Body and the IAC. and the TB.
Blow out yhe (TPS) trottle position sensor or at least work the butterfly valve 20-30...

Just a thought. Fog lights are to be a broad 170-180 deg spread left to right and narrow height to shine under the fog.
If you mount “fog” lights in the back of the holes you will be cutting most...

How steep is this mountain?
How full is the oil?
What brand oil filter?


Here is something dug up with a 2 min search. Might be usefull
3.6 Pentastar Oil Gallery plug TIP. Cam phaser Ticking...

That is a cam position sensor code?

Does your oil need to be changed?
Are you using the correct weight oil?
They skip bad cam sensor or wiring.

Cause:
ENGINE OIL LEVEL LOW
ENGINE OIL...

Try here or hella or PIAA
Universal, Jeep & Truck Fog Lights | KC Lights


Never look down on anyone unless you are helping them up - Jesse Jackson

All those j’s. Super j’s


Never look down on anyone unless you are helping them up - Jesse Jackson

The bolts are torx so be sure to clean the torx star of paint. Get a good sharp corner bit that fits tight. Heat the bit and bot while bit is in to loosen rust or any loctite used.
Work bolts back...