Search results

What do ruptured pipes have to do with a Carter AFB?

I may have been a little rough handed when I last adjusted the floats and I understand that it takes more finesse than that. I hope to get to it in the coming days.

Yep that's just where I'm leaning too. Thanks

Yep, that's just what it's doing. I've clumsily ran a bit of fuel down the carb and it seems that I may be dealing with maladjusted floats.

Okay gang, by now I think I may have it narrowed down to a goof I made in setting up the floats. Long ago I took the fractional data for setting the floats and float drop to decimal so I could use my calipers. I think I may have misinterpreted the calculation or just took a false reading. The...

I was checking the Air Screws and what do you know, some gremlin maladjusted them. On the primary side it was nearly at its stop. Going to adjust the Floats again and take it from the top.

As a sidebar, I'm still running the Ford EEC-1 Ignition Control Module that was stock on 'Black Betty'

Thanks Terry! Yep, something like that was what I was looking for but I got impatient. Mustie 1 has the one I was looking for https://www.youtube.com/@mustie1

Today while I was out to Physical Therapy I stopped by NAPA looking for a Fuel Primer Bottle. Heretofore, I was pouring old fuel into a carb cleaner lid and clumsily adding fuel to the primaries. At NAPA all they had was an oversized Battery Filler so I figured if it's impervious to battery acid...

Thank Terry, I'm being criticized on another forum where a couple of kind folks insist this is a fuel issue. With the double whammy of the low voltage from the Starter Solenoid and the open from the Coil to the 13B Terminal of the Dash Connector I'm convinced that this is electrical.

Okay I grounded the Starter Solenoid and she spun up just fine. I removed the Cap to the MSD and watched the Rotor make several turns without pause. That's a relief. I'm going to try checking out the under dash connection panel and the Key Cylinder next once it cools down. 101 today.

Knulla she won't turn over at all now. edit Vittu Minua, I forgot to ground the Starter Relay

I'm hip Samuel, this state is only when I take it beyond my normal startup. Last year one blip of the throttle to set the choke and she took off.

(y) That's great, I wish I could find an affordable one for my '78 CJ

After running through the DARS chart in the TSM I seem to be grasping at straws. On another forum one Jeeper had a similar issue and traced it to the ignition switch itself. Many years ago I found mine increasingly harder to turn. I took it apart only to find that a PO had inserted a wood screw...

Thanks Terry, I've seen those too, once I get the ignition fixed on 'Black Betty' I'm going to have one fabbed up by the guys that married my Kentrol roll bar and 'family' cage turning into a 6 point roll cage. They do stellar work.

If you have more bent leaf springs...... You'd better replace them. :p On 'Black Betty', she came with a 2" lift (Superlift) and 32" tires. After going with BFG KM2's I took her to a local shop for alignment and they thoroughly screwed up. The steering would pull lock to lock. Taking it to...

When I rotate the throttle lever there's fuel coming out of the Accelerator Pump nozzles and when I take it too far there's fuel coming out of the Bowl Vent Tube

Hi Gang it's been a long time. Over the last year and a half 'Black Betty' has been giving me fits with the Ignition system. (1978 CJ5 w/360) I've installed a new Primary Battery (I have a 2nd one for my winch) and I've tried replacing the Starter Solenoid and checking the wiring from it to...

Hi gang, been a while since I last posted. 'Black Betty' is doing fine and I have an MSD 6 waiting in the wings for an ignition upgrade. I once saw what looked like a full coverage Con-Ferr front shield that covered the front of the oil pan, the steering gearbox and other front impact areas...