Search results

I just recently installed a locker that I got from www.4wheelparts.com for $245, and first of all the instruccions were kinda dirty with gresse as if it was a used item, but I think it could have been just the packing procedure, anyway, once it was installed I notice that i has put a little more...

:D I had recently changed my front R&P from a 3.07 to a 4.11 and this weekend I swaped the rear ones, got a donor from a junkyard '86 4 cyl cherokee, everithing went very very smooth exept for the fact that I'm a little worried about tha fact that I might have left the carrier case to tight...

:x , I just started to install new gears on the front of my YJ, for witch I have to remove the hole hub assembly to get the axels out but the bearing carrier just wont come out, Is there a special tool for this?, Is it not sopoused to be stuck?? and worst of all I have no agle to hit it with my...

Lets say I got $300 saved up, and could only afford one detroid ez-locker for the front or rear of my 88 6cyl 5speed YJ. its got 4.11 gears and 31" tires Here's the question, where thoes the locker have more off-road performance , ther rear or the front?? what do you guys recomend the front...

Hi, I have a friend that has a 86 4 cyl XJ jukedup, and sell's me his front diferential with the 4.11 gears for $50 bucks. Here's the cuestion :?: , Can I fit them (R&P and Case) in to my Dana 30 diferential?? Are they compatible? Thank's a lot for your help... , i'm really interested in this...

Hi, this is I think the most asked question from the newbies like my self, sorry, bus I was wondering how low can I take the pressure off my tires while off-roading, running AT 31"on 7"wheels , most the offroading is made on steep hills of desert sand, .001% rock.... thanks a lot for your...

Suggestions for a "2nd" Vehicle? Hi, I have an '88 jeep YJ with 1 1/4" shackels and 3" body lift , and want to now if I can fit 33" tyres into it.... Thanks four your help......

1043312 I just decided remove the trany and pay a visit to my clutch and it turn's out that the clutch pilot bearing was totaly destroyed (go figure) the only thing left was the outer ring, but it wont cum out, i've tried extractors, hamers, hidrolic tecnics, etc, but nothings worked, Im...

1043444 I just reacently changed the clutch on my jeep and a very weard shake has developed, every time I get a green lite (after stoping) , the jeep shakes for a second and then it takes off, like it slips or something( its kinda like I was new to driving manual transmition) after that its all...

1044147 I, i've gone from a perfectly awesom 88'XJ to my newly acuired YJ ive had it for 2 weeks and in that time ive changed the clutch, power stearing punp, rear track bar axel braket, tuned it up, prepeared it for winter and gave it a good wheather protectent undernith, now I want to rebuild...

1048233 Hi, mi name is geronimo, I live in Mexico, I have a 88 Yj with a 4.2L, manual trans, that has some mods, starting with msd ingniton 6AL, Blaster 2 Coil, Tach Adapter 8910, no cat, and recently changed the timing set, and carburator for a Carter 2 Barrel that I got in a junkyard in very...

1066670 I reacentoy changed the preasure sending unit becouse the last one would not send a signal, but the new one send's minimum 40psi of preasure that's at idle and the jeep fully warmed up. Is there something as to much preassure... :-? , or is there somthing stuck inside?? o what....[addsig]

1067116 Can somebody tell me the importance of the rear track bar?, since I got my jeep the rear track bar bracket on the axel was totaly destroyed ive welded it back on but it just keeps on braking (do I suck at welding o what :-P). sow I decided to take the hole thing off, the cuestion is...

1067223 Here's a dumb cuestion, how hard is it to swap the pinion and the ring from a cherokee to a wrangler for the dana 35 and 30 diffs. couse i want to go from a 3.something to the 4.10, :-) you could say im very mecanicaly inclined but that swap kinda intimidates me a little couse ive...

1068328 Hi, i was wondering, do i have to change the R&P on the 2 axels when i do a swap or can i just change the rear one, from a 3.31 to a 4.11?? Thanks for the help... :-? [addsig]

1071582 Hi, I have a 88 Yj with stock 3.07 gears and when I put in 31" the engine lost most of its performance. Sow I am very interested in swaping my gears to 4.11 at the least. Sow I shoped arround and found a shop that would rebuild my axels (bearings, seals, etc..), use used R&P and, and...

1073611 Hi, after loking in almoust every junkyard I now, I found an old '86 XJ with 3.73 gears, my jeep has 3.07 and Im running 31" with the 258, and I with that gearing ive lost the performance it had, sow I was wondering , will the gears and cases fit into my diferentials, or are they not...

1073780 has anyone installed a crane cams power max camshaft?, im going to shange my lifter couse they are all tappy, and I mite as well add some performance, but will I get it from this camshaft???[addsig]