Search results

1045085 This site has some good info They also sell parts. That exploded diagram may be a bit hard to read, but should help some. Things I've found with my weber. A fuel pressure regulator is almost a must with it. Depending on what you read, weber recommends 3 to 3.5 psi MAX fuel...

1045086 just wanna add some thoughts. sometimes when I engage the hubs, I'll just reach under, grab the front drive shaft, and twist it till I feel it lock. if you have open diffs, you know you have both hubs locked then, if your transfer case is still in two-wheel or neutral. I leave my...

1045142 from about 2 rpms to about 1500 rpms. well, not that bad, I think they list the torqe peak around 1900 and the horsepower peak around 3000. From what I've read, its common for factory ones to run out of breath around 3500, my old motor did. Some say a good a good ignition upgrade...

1045220 The capacity, according to haynes, for the AMC v8's is 5 quarts, unless you have an aftermarket oil pan. I'm afraid I can't help with dipstick length. Either way, I would try to avoid running too much oil untill you figure out why your dipstick is inaccurate. -keith[addsig]

1045221 this might help some. I'd guess the wire broke or came off the sending unit at the tank or on the way there. or a ground at the tank broke. -keith[addsig]

1045238 <TABLE BORDER=0 ALIGN=CENTER WIDTH=85%><TR><TD><font class="pn-sub">Quote:</font><HR></TD></TR><TR><TD><FONT class="pn-sub"><BLOCKQUOTE>The 258 holds 5 or 6... the manual says six... but mine seems up to snuff after 5.</BLOCKQUOTE></FONT></TD></TR><TR><TD><HR></TD></TR></TABLE>...

1045271 I tried to find an online diagram for ya, but had no luck. I take it you aren't using a vapor canister or anything. berretajeeps idea will help keep dirt out, but won't help keep gas in much. the bad thing about venting to air is, your jeep will probably stink like gas and depending...

1045364 <TABLE BORDER=0 ALIGN=CENTER WIDTH=85%><TR><TD><font class="pn-sub">Quote:</font><HR></TD></TR><TR><TD><FONT class="pn-sub"><BLOCKQUOTE>thanks for the input. I think if I get the filters up higher than the in spout( gas cap) it will work. Do you have to order the vented gas cap special...

1045368 I think 1980 may be an uncomputerized version of the BBD? here is some info on one particular BBD issue To answer the choke question. Gasoline does not evaporate/atomize or explode well when very cold. one solution is dump a lot extra in to get it going. In a fuel injected system...

1045529 from my experience, they are normally friction fit and don't need to be sealed, but I don't think they are all the same. On my six it was tight, I had to punch it out from the bottom to not wreck the tube. You may end up clamping on to it and yanking hard to get the old one out, or it...

1045568 I've liked my t-5's. never had a problem with one. This site has some info on t-5's. -keith[addsig]

1045829 well, I don't wanna re-invent the wheel, so I did a google search. This is a good article on replacing a clutch, although its not it a jeep. I don't know what size clutch you have. also, if your clutch is literally "smoked", you may wanna check the flywheel for hot spots/ cracks. It...

1046057 Are you asking if that Brand kit is quality? or if the basic premise is a good design? or both? I maybe can aswer the second one, my Toyota has a home brew version of that on it and it seems to work quite well. they guy that built the truck used to race SODA, and the quickness of the...

1046147 If you are talking stock, the are not designed to be adjustable. they are designed to collapse in the center only in an accident, so the the steering wheel isn't rammed through your chest. that stings. They also usually collapse a short distance at the rag joint at the steering box...

1046834 <TABLE BORDER=0 ALIGN=CENTER WIDTH=85%><TR><TD><font class="pn-sub">Quote:</font><HR></TD></TR><TR><TD><FONT class="pn-sub"><BLOCKQUOTE> The 4.0L is the exact same motor just bored to a smaller bore. the 2.5L is the exact same motor but just literially has 2 less...

1046927 hmmm, I never heard that the 700r4 was significantly weaker than a TH350, I always got the impression it was equivalent. I have heard it is more difficult to rebuild and is less forgiving in a rebuild than the TH350. Personally, if you know it'll bolt on with out much problem, and...

1046928 If its stock '84, its not. I believe that the WC didn't come in till '87 +- a year. I also don't believe WC ever came in a jeep. it -is- a better transmission, but not -that- much better. better bearings and a few parts upgrades. I'm looking for a site on it now, I lost my link...

1047351 this isn't gonna turn into a flame fest like q-tec, is it? I own an REP8000 and it seems like a nice winch to me. got it used, its pretty beat up but its still kickin'. I think more important than brand, is what you are looking for. series wound vs. permanent magnet motors. line...

1047987 just wanna add some opinions. 2L is pretty much never needed, but it can come in handy if you use the jeep as a "workhorse" and are moving heavy loads on pavement, or pulling brush, or something and you don't want that 4-wheel-bind from 4L on pavement. with my twin stick, I play with...

1043476 not to contradict tim, but is it just a little clutch chatter you have? you just replaced the clutch, or also pressure plate? Sometimes more aggressive clutches don't like to slip and if you try to force them to slip, they'll chatter. clutches are also directional, but I'm not sure...