Search results

I need to have a new starter ring put on my flywheel. The teeth are nibbled off enough to need to be replaced.. My question is,, in shopping for a new one, a new ring is like $18 a new flywheel is like $142,,, but both together allready assemled is like $200... Is it that hard to put the starter...

Axle donar for cj5 I knew a guy that took the power steering "stuff" out of a,, I think wagonner.. and convereted his Cj to power steering,, Does anyone know the types of vehicles, year make, and what all would be needed to convert from, oh my hurts steering to power steering in a 82 CJ 5...

I have seen and heard of people getting wider and stronger front and rear axles from donar vehicles,,, which donar vehicles have the least amount of "conversion" and work the best for a 82 cj5???? Some have said with a dana 44 you have to use TJ springs????

If you had $500 to put into your Jeep,, what would you do... ????

I have taken my starter apart to put a new starter gear in it.. I have taken some things apart that i should not of but i have gotten them back together.. my issue is, i have about a 2 to 3 inch black spring left, and i do not know where it goes,, i presume near or on the starter gear but...

Minimum amount of bodylift for a belly up? Recently my Jeep failed to start!! The starter buzzed like bees, but no contact.. I took the starter off and the the outedge of the starter gear teeth were rubbed down.. I looked into the belly of the jeep and the starter ring, flywheel, also was...

I have a Weber Carb that I have installed, and not sure if I have have all lines ran correctly.. Does anyone know where to find online pictures of how the lines are supposed to be ran???Thanks for any help..

Ok,,, When I start up the oil pressures sits around 70,, as I drive along and the engine warms up, it drops. It usually will sit somewhere between 0-5... Its a brand new guage and sending unit,, It is an electrical guage, and it is on a 82-cj5 6 cycl... I know as the oil warms, that will cause...

I have just completed the Blazer heater blower upgrade.. I also installed a new heater core.. I ran the jeep for a while, but all I got was cold air.. Is there something else I have to do.. Prime the core? and if so how? Thanks THomas

Ok,,, the gremlins are at it again... Last night my head lights and dash lights would not stay on at the same time. If they were both on, they blew the fuse quicker than you could say, stop... They will stay on and not blow by the eaches, but not at the same time.. I know shorts are hard to say...

Ok,, I have lifted my '82 CJ-5 by 4" and now it looks like a pine tree,, tall and skinny. I know of some people that have swapped axle assemblies from other vehicles to widen out the trac... But I don't know what type of vehicle they came from? Any ideas of what to do best to widen the bottom...

I have a '82 CJ-5 with a T-150 3 speed transmission... On the top of the transmission is a 2 headed plug. It has to spade type connectors, one turned one way and the other exactly the opposite of it.. what is this for?

I just had a new bell housing and a new clutch installed in my '85 CJ-5, 3 speed straight six Jeep. When I drive it now, the clucth pedal only has to be millimeters from the floor to start to engage,, If I ride the clutch, at all, I can hear the clutch spinning and my wheels are going no where...

I have recently purchased a set of 2" wheel spacers to widen out my lifted '82 CJ 5. I know this adds a bit more stress underneath, and wondered was there any additions or changes to the underneath that would help with this added stress? Thanks for your help THomas

I have a '82 CJ 5, 6 cycl with a weber carb. Even before I put the new carb on, I keep blowing the seal under the valve cover. Two shops have resealed it, with and without gaskets. The most recent type at the shop to do this, it held for a day then started leaking on the drivers side. As I was...

I just put on a TFI upgrade, new high pro coil, larger distro cap, new plug wires. I put the wires on in the firing order that it showed. When I try to turn it over, she turns but does not hit to start. I have check the sparkplug and wire connections for fire going to the plugs, and there is a...

Air/fuel gauge I am trying to remove my steering shaft, to put new bearings at the top end of it.. How is the best way to get this done? Remove the manual steering box and remove shaft? It is on a '85 CJ 5,, thanks thomas

Is this something to install in a 85 cj 6 cycl,, or just a waste of hard earned money... thanks