Search results

Cant see the pic. :( od

What bolts do I need for a transfer case drop? pretty sure, but i could have missed one. Ill check it tomarrow after work. od

Double clutching is what is done on transmissions without synchronizers like a rig or dumptruck. It is basically the act of getting the drive gear in the transmission to go the same speed as the next higher or lower driven gear. On upshifting you: 1) push in the clutch. 2) pull into neutral. 3)...

The other day i noticed that my drivers side turn indicator wasnt flashing, it was steady, so this to me indicates a blown turn signal bulb. I replaced the bulb and its still the same. The passenger side signals work fine so i dont think its the relay and the fuse is fine. Could it be the turn...

Could be ur clutch going out. Try this When ur standing still in neutral with the clutch pedal up and the engine running push in on the clutch and try to put it in reverse a second or so after, if it grinds its a sign that ur clutch is going bad. Or try this, while setting still and the engine...

I had a 97' Blazer and it had part time 4x and low range. I dont believe it was a special edition or anything but im sure it was part time and it had low range. od

Was there any dirt, dust or something on the rotor and/or brake pads? Could have dirt embedded into the pad maybe not sure if this can happen or not but u could try switching the sides that the pads go on passenger to driver and visa versa to see if the noise switches sides too. od

I used to have a 97' blazer and it did awesome in the snow. Im not sure what 4x4 system it has but it has two electronic switches on the dash. One was for 4high and one was for 4low. Never really had it offroad too much but I dropped the front passenger tire in a drainage ditch along a mountain...

I used a 7mm on mine. od

Thanks joopin. Let me know how it turns out . od

I was looking at the rear of my jeep today trying to figure out the best way to tie a custom bumper into the frame. I looked on www.jeepfabrication.com and they show how to tie it in to the frame but they only show tie-ins on tj's and I was wondering how I could do this on a yj with the shackles...

As I laid in bed last night I was thinking that that might be how it goes. Im pretty sure the front is the pcv and the back is the intake vent. Since i done have the stock air cleaner does the vent line still go to this or could I put a crankcase vent on it like a chevy has? I have the...

MINGEZ!!! I checked all the pcv lines and they are all fine. The only constant vaccuum line that i have off of the mc carb is on the rear passenger side of the carb and that is where i had it attached to, i tried having it attached to the port on the bottom of the edelbrock breather and the...

im thinkin its the rings unfortunately. When I rebuilt the engine though the tollerances all checked out and the walls werent scored or anything. Should I do a compression check? Thanks for any help od

:x OK. No matter how i hook up the pcv i still have enough pressure to make oil come out of the dip stick tub. I have the short dipstick tube, its like 3 inches long. What is the problem here?? Would a longer dipstick tube fix it or does the engine just have too much blowby. In my opinion the...

Thanks guys. I actually ended up doing what west747 said and squared off a bolt and it worked just fine. I hear ya derff96963 but the money has to be there first :) . od

Ive been fixen on changing the transmission oil but i have yet to come by something to fit the transmission drain plug. It looks as though a 3/8 ratchet will fit it but its too big so i tried 1/4 and thats the too small. Is there a special socket that is made for this kind plug or do i have to...

Apparently they are one in the same. I got the seal at autozone and they had it listed as 231 but it fit my 207. Thanks guys. od

My tail shaft seal has been leaking for a while now and ive finally got a chance to replace it but i was wondering if the seal for the 231 can be used on the 207 because i havent been seein many oil seals for the 207. I appreciate any help. Thanks. od

Try measuring it up or u could take the gate off of ur CJ and see if it lines up b4 u buy it unless its on ebay. I believe to a certain year the wranglers with the factory hardtop had the framed in lift gate like the CJ hard tops, then they went to the full glass liftgate. Im not sure of this...